Inspection History Details
Inspection Status: Approved
Inspection History: SIGN SITE REVIEW
| Date | Description | Inspector | Results | Comments |
|---|---|---|---|---|
| 03/14/2013 | SIGN SITE REVIEW | Approved | SET-BACK APPROVED BY DAVE ROBERTS | |
| 03/11/2013 | SIGN SITE REVIEW | Partial Approval | CONTRACTOR SUBMITTED REVISED DRAWINGS 3/11/13. ALL REVIEW COMMENTS HAVE BEEN ADDRESSED, SENT OUT FOR SETBACK/GRADE HEIGHT INSPECTION CHECK. CONTRACTOR TO HAVE SIGN LOCATION MARKED. |
|
| 03/05/2013 | SIGN SITE REVIEW | Correction Required | REVIEW BY HEATHER THRALL, COT, PDSD - SIGNS SECTION (heather.thrall@tucsonaz.gov) ERIC NEWCOMB, COT PDSD - STRUCTURAL (eric.newcomb@tucsonaz.gov) RAY MAJUTA, COT PDSD - ELECTRICAL & OUTDOOR LIGHTING CODE (ray.majuta@tucsonaz.gov) FOR: CULVER'S BUTTERBURGERS & FROZEN CUSTARD AT: 4810 N 1ST AVE ZONED: C-1 COMMERCIAL, SCENIC ROUTE PERMIT: T13OT00242 ** Several parts of submittal note "LED strip accent lighting" - these are not signs. A separate electrical permit & review is required for these lights. Contact Ray.Majuta@tucsonaz.gov or at 520-837-4988 for permit information. SECTION 3-82, SCENIC CORRIDOR DISTRICT OF THE SIGN CODE SECTION 3-18 PERMITTING REQUIREMENTS NATIONAL ELECTRICAL CODE (NEC) 2011 OUTDOOR LIGHTING CODE CHAPTER 5 1) Several pages of the submittal have note in red "NOT FOR CONSTRUCTION - PRELIMINARY". These drawings are for construction, installation and inspections once sign permit is issued. Remove or cross out note. 2) Regarding MONUMENT SIGN "sign A" - A) Demonstrate compliance with 3-82.E.3.d.2 - must be 150' FROM centerline of River, Scenic Route. B) Appears sign does not meet 3-82.E.3.f - Lighting: Sign panels shall be opaque. Light shall be emitted through individual translucent letters and/or symbols only, or individual letters and/or symbols may be halo illuminated. Unused tenant panels shall be opaque and designed to match the rest of the sign. Contact staff for an appointment to discuss a possible solution. C) Provide electrical detail diagram (Type of illumination? Shut off switch & timer) *Acknowledged handwritten on plans: volts, amps, circuits. 3) Regarding TRAFFIC DIRECTIONALS "signs B1 & B2" A) show shut off switch and timer 4) Regarding MAIN MENU BOARD "sign C" A) dimension - IN FEET - at minimum 12 point font (for records) & show total sign area on the plans B) clarify conflicting height on application versus the plan (max height 7') C) show shut off switch and timer D) plans states "varies" for depth/width of footer. Provide exact footer depth/width - dimensioned diagram. 5) Regarding (4) ILLUM WALL SIGNS "D.1-D.4" A) show shut off switch and timer B) dimension -IN FEET - at minimum 12 point font (for records) & show total sign area on plan 6) Regarding ILLUM PRE-MENU BOARD "sign E" A) dimension -IN FEET -at minimum 12 point font (for records)/show total sign area on plan B) show shut off switch and timer C) plan states "varies" for depth/width of footer. Provide exact footer depth/width - dimensioned diagram. 7) Regarding "cooked to order & handcrafted" sign labeled as incidental: A) Per Sign Code definitions and Section 3-51, This is not an incidental sign, it has advertising copy on it and it's over 2 sqft.. Note, there is sufficient sign area to add this sign to the permit, providing it is mounted flat against wall to meet wall sign definition, otherwise it would need to be removed from the package. 8) Note: the sign area allowance calculations listed on the plans for attached building signs are incorrect. Attached sign area is 1.25 x building street frontage = 1.25 x 102.43 (1st) + 1.25 x 52.81(River) = 194 sqft. Divided among elevations. |